Simulate the induction heating process with the 3D coil design
Keywords:
Injection molding, Dynamic mold temperature control, Induction heatingAbstract
In the field of dynamic mold temperature control for injection molding process, the induction heating method has many advantages as high heating rate, low energy consumption and reduced environmental pollution. In this research, the simulation method was used for determining the heating rate and the temperature distribution of the 3D coil induction heating. The result shows that the heating rate can reach to 30oC/s at the mold surface, and the temperature distribution has a clear improvement when we compare with the other coil design. With the 3D coil design, the higher temperature appears at the center of the mold plate with a rectangular area.
Downloads: 0
References
Lê Minh Trí, Tối ưu hóa giải nhiệt khuôn ép phun, Luận văn Thạc Sĩ ĐH Sư Phạm Kỹ Thuật TP. HCM, 2006
Nguyễn Văn Thành, Nghiên cứu xây dựng quy trình thiết kế hệ thống làm nguội cho khuôn ép phun nhựa theo công nghệ CAD/CAE, Luận văn Thạc sĩ ĐH Bách Khoa TP.HCM 2006
S. C, Chen, Y. U. Wang, S. C. Liu, J. C, Cin, Mold temperature variation for assisting micro molding of DVD micro-featured substrate and dummy using pulsed-cooling, Sensors and Actuators A 151 (1) (2009) 87-93.
S. C. Chen, Y. W Lin, R. D Chien, H. M. Li, Variable mold temperature to improve surface quality of microcellular injection molded parts using induction heating technology, Advances in Polymer Technology 27 (4) (2008) 224-232.
M. C. Jeng, S. C. Chen, P. S. Minh, J. A. Chang, C. S. Chung, Rapid mold temperature control in injection molding by using steam heating, International Communications in Heat and Mass Transfer 37(9) (2010) 1295-1304.
S. C. Chen, Y. Chang, Y. P. Chang, Y. C. Chen, C. Y. Tseng, Effect of cavity surface coating on mold temperature variation and the quality of injection molded parts, International Communications in Heat and Mass Transfer 36 (10) (2009) 1030-1035.
S. C. Chen, H. M. Li, S. S. Hwang, H. H. Wang, Passive mold temperature control by a hybrid filming- microcellular injection molding processing, International Communications in Heat and Mass Transfer 35 (7) (2008) 822-827.
P. C. Chang, S. J. Hwang, Simulation of infrared rapid surface heating for injection molding, International Journal of Heat and Mass Transfer 49 (21-22) (2006) 3846-3854.
M. C. Yu, W. B. Young, P. M. Hsu, Micro injection molding with the infrared assisted heating system, Materials Science and Engineering A 460-461 (2007) 288-295.
S. C. Chen, R. D. Chien, S. H. Lin, M. C. Lin, J.A Chang, Feasibility evaluation of gas-assisted heating for mold surface temperature control during injection molding process, International Communications in Heat and Mass Transfer 36 (8) (2009) 806- 812.
S. C. Chen, P. S. Minh, J. A. Chang, Gas assisted mold temperature control for improving the quality of injection molded parts with fiber additives, International Communications in Heat and Mass Transfer 38 (3) (2011) 304-312.
Downloads
Published
How to Cite
Issue
Section
Categories
License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Copyright © JTE.
